MADE TO MEASURE FINISHING TOUCHES

 

INTERNAL MOULDINGS

 

ROUTER

We use a roman ogee pattern. This is a more decorative design, with a more traditional feel.

This design is pictured in sapele.

BEVEL

We use a 20° on the casement and a 9° on the frame. This gives the window a much more contemporary, smooth lined feel.

This design is pictured in Sapele.

 

OVALO – BEVEL

We use an Ovalo on the casement and a 9° bevel on the frame. This gives the window a traditional feel with a contemporary twist. This design is pictured in Softwood.

FULL OVALO

We use an Ovalo on both casement and frame. This is the most traditional window mould and is pictured here in Softwood. This mould requires the purchase of the multipoint locking system #

# If you would rather not have the Multipoint locking system then you will need to add 10% to the cost of the windows as we have to use a larger section of timber for them. The multipoint locking avoids the need for this extra timber. 

 

LISTED BUILDINGS

We now have the facilities to match your grade II listed buildings windows as near as possible. This includes the thinner glazing bars typically found on them, and the scribe jointed corners expected on this type of windows. Please see towards the end of the guide for the moulds we can do, and details of the thinnest glazing bars possible with the different moulds. We cannot always give a true 100% match, but we will get as close as possible. If you need this type of quote please enclose some photos along with the quote request form at the end of this guide.

The above moulds are what we can use on your listed buildings windows.  The bevel facilitates the thinnest bars at 21mm. The Router and Ovalo moulds both require 30mm thick bars. This is only achievable on single glazed windows. Below are examples of each mould.

 

 

21mm Chamfered Bars

Pictured is a Yorkshire sliding sash with scribe jointed 21mm Chamfered glazing bars.  

These are the thinnest bars we can achieve.

 

  

30mm Ovalo Bars

Pictured is a traditional window with scribe jointed 30mm Ovalo glazing bars.

On this window we have used a 9° bevel around the frame and an Ovalo mould on the casement and glazing bars.

 

MULTIPOINT (ESPAG) LOCKING SYSTEM

We now have the option of fitting your new windows with a more secure multipoint locking system. The advantages to this are as follows:

The system can be fitted into any of our windows (with the exception of sliding sash). We highly recommend this system due to its security and its quality.

Pictured below is a window with the espag locking system in- The window is a traditional georgian window in Idigbo, with satin chrome ironmongery.

External View of the Window

Internal View of the Casement

Open View of the Casement

The pictures on the right  show the casement opening. On the open view you can see the receiving plates for the locking bolts and the Friction Hinge at the bottom of the casement.

The photos on the left show the multipoint locking system. This system shoots the hook bolt shown into a receiver housed into the frame. This is the locked postion. When the handle is lifted the bolts retract so they are flush with the edge of the casement and the window will open.

We can also install a nightvent facility at no extra cost so the windows can be locked, but allowing an airflow. (this does not replace the need for trickle vents when vents are required).

The cost to install this system is £40 per casement (opening part). For this you will get the Locking system installed, the casement will be hung on friction hinges as opposed to standard hinges and the locking handle will be included (any of the below finishes)

The handle left is what we supply as standard with the espag system. Its available in the following finishes:

Brass, Chrome, Satin Chrome, Black, Bright Bronze, Satin Bronze and White

We can supply handles in Antique Black (£10 extra) and Pewter (£15 Extra) see pictures below in the ironmongery selection section for style.

 

IRONMONGERY SELECTION

Black

White

Brass

Chrome

Black Antique (also available in curly tail)

Pewter Antique

 

EXTRAS

Extra

Price

Dummy Casements

Price

Trickle Vents

£10 per vent

Basic Casement

£60 in softwood

Friction Hinges

£15 per casement

Centre Bar

£70 in softwood

Black Antique Ironmongery

£10 per casement

Cottage

£80 in softwood

Pewter Ironmongery

£15 per casement

Georgian

£90 in softwood

Multipoint locking system

£40 Per casement

Hardwood dummy casements

£P.O.A

 

READY TO ORDER?? Please click here for a printable order form. When you have completed the form please email it through and we will price your windows.

Click here to download our PDF window guide that contains all the information on our made to measure from these pages.

 

OPTIONS FOR MASS PRODUCED WINDOWS

 

The windows are fitted as standard with trickle vents and draught seal. The colour options are as follows:

Trickle Vents - White or Brown

Draught Seal - White, Brown or Beige

 

The handles on the left are the colour choices for the mass produced windows. You can select which colour you require on ordering.

The finishes on the left are what we can offer for your windows.

The prices for the windows include either a base coat stain or a white primer for you to finish on site.

If you want a factory finish the SFF and HFF prices need to be added to the window price.

Please note, the optional finishes come with an extra cost of 5% on the finishing prices stated. Please state which option you want on ordering.

The glass options on the left are available on request. They are ideal for bathrooms or any situation where obscured glass is needed.

There is extra cost involved in these glass options.

If you need these options for the windows please state on ordering and we will get the price for it.